What Are Euromap 63 and Euromap 77?

What Are Euromap 63 and Euromap 77?

Euromap 63 and Euromap 77 are two interface standards defined for getting production and process data from plastic injection moulding machines. Euromap 63 represents the classic file-based method, and Euromap 77 the modern information model built on OPC UA. Both have the same goal: to make injection moulding machines of different brands monitorable through a common data language.

In brief

  • Euromap 63: the machine writes a text file to a shared folder; the monitoring system reads it. Widespread but old.
  • Euromap 77: an OPC UA-based, real-time modern interface with standard field names.
  • Both provide data such as cycle count, cycle time, mould number and process parameters.
  • It is the main gateway for MES integration in the plastic injection moulding sector.
  • If there is no interface, basic production data can still be obtained with counter/signal-based collection.

How does Euromap 63 work?

In Euromap 63, the machine controller regularly writes files to a folder on a network share. The monitoring software creates a session file to state which data it wants, and the machine produces the data file in response.

  • Pro: It is very widespread; it has been on most machines in the field since the 2000s.
  • Con: Because it is a file exchange there is latency; sub-second resolution should not be expected.
  • Caution: Folder permissions, file locks and housekeeping (deleting old files) often cause problems during setup.

How does Euromap 77 work?

Euromap 77 works through an OPC UA server. The machine publishes an OPC UA server; the MES connects to it, subscribes to the nodes it is interested in, and data flows automatically as values change.

  • Field names are standard; you do not have to rewrite the mapping table when the brand changes.
  • Thanks to the subscription model, latency is low and the data can be considered real-time.
  • OPC UA’s authentication and encryption features come into play, which is better for OT security.

What data is obtained?

DataUse
Cycle count and cycle timeProduction count, performance, OEE
Machine status (production/stopped/alarm)Downtime analysis, Andon
Active mould informationMould life tracking, work order matching
Injection pressure, temperature profile, dosingProcess monitoring, quality correlation
Scrap/reject counterQuality rate, scrap analysis

Which one should you choose?

  1. If your machine park is mixed, plan to use both together. Euromap 77 on new machines and Euromap 63 or signal-based collection on old ones is a realistic combination.
  2. If you will analyse process parameters, Euromap 77 is preferred; its resolution and field standardisation are better.
  3. If you will only track counts and downtime, Euromap 63 is sufficient in most cases.
  4. Check the licence: With some machine manufacturers, the Euromap interface is an option unlocked with an additional licence.

Common mistakes

  • Assuming the interface “exists” on the machine; the option was not ticked at the time of order, so the interface turns out to be disabled on site.
  • The Euromap 63 folder filling up and slowing the machine down or stopping it from writing.
  • The work order match staying empty on the MES side because the mould number was not entered on the machine.
  • Not modelling how the cycle counter resets, leading to jumps in the production count.

Frequently Asked Questions

What is the difference between Euromap 63 and Euromap 77?
Euromap 63 is file-based: the machine writes text files to a shared folder and the monitoring system reads these files. Euromap 77 is a modern information model built on OPC UA; data flows in real time through a subscription model and field definitions are standard.
What should I do if my old injection moulding machine has no Euromap?
On machines without a Euromap interface, collection can be done via counter pulses, relay signals or digital outputs in the machine’s panel. This method yields cycle count, running/stopped status and production count; process parameters cannot be obtained.
Is Euromap 77 replacing OPC UA?
No, Euromap 77 is built on top of OPC UA. OPC UA provides the transport and security layer; Euromap 77 defines the common information model specific to injection moulding machines, that is, which data is provided under which name.

Euromap 63 and 77 in EFFIX MES

EFFIX MES offers Euromap 63 and Euromap 77 among the field protocols it supports; OPC UA, MQTT, Modbus, EtherNet/IP and MTConnect sit in the same layer. On old presses without the interface, counter-based collection can be done with the Inolink wireless IoT network, so a mixed machine park comes together in a single production model. Incoming cycle, status and mould data feed real-time production monitoring, downtime records, the OEE calculation and mould/tool life tracking; process deviations can be tied to alerts with the Proactive Alert System (PAS) detectors. To discuss the right collection method for your injection moulding line, visit the EFFIX MES page or request a demo.